cover-crops-usda-ars

Q+A: Herbicide use with cover crops

Paying careful attention to herbicide labels, cover crop selection, research results, and the timing of herbicide application and seeding can help increase your odds of successful incorporation of cover crops into a corn and soybean system. 

As more farmers look to plant cover crops in their corn and soybean fields, the question “What should I do about my herbicide program?” often arises. There is not a one-size-fits-all answer to this question, and unfortunately there are many unknowns. 

One challenge when adding cover crops into a corn and soybean production system is that herbicides with residual activity may interfere with the establishment and growth of cover crops. Residual herbicides, however, are a key weed management tool, especially in the management of herbicide-resistant weeds and when combatting weeds with extended emergence patterns like waterhemp.

A key first question - will the cover crop be grazed or harvested for feed or forage?

If the answer is yes, then any rotational or plant-back restrictions listed on the label MUST be followed. The herbicide label is a legal document and instructions must be followed to avoid violation of federal law. If a rotational restriction is not listed for a particular cover crop, the rotational restriction listed for “other crops” must be followed.

There is more flexibility if the cover crop will not be grazed or harvested. The farmer assumes all risk of injury to the cover crop if label restrictions aren’t followed, but there would be no legal issue of trying to sell an “adulterated crop,” since the cover crop is not entering the food or feed chain. 

If the cover crop will not be grazed or harvested and the cover crop is not listed on the herbicide label, consider the following six questions to help reduce the risk of crop injury while increasing the potential for successful cover crop establishment.

1. How sensitive is the cover crop to herbicide carryover?

Several universities have been conducting research to address this question. Results of research conducted by the University of Missouri from 2013 to 2015, looking at the general sensitivity of cover crops to carryover from a number of common preemergence and postemergence herbicides, is summarized in Figure 1. Of the cover crops evaluated, they found tillage radish was the most sensitive to herbicide carryover, while cereal rye and hairy vetch were the least sensitive. Similarly, in greenhouse trials conducted by Iowa State University Extension to simulate herbicide carryover in the field, Hartzler and Anderson found that radish was the most sensitive of the cover crops evaluated while cereal rye was the most tolerant.

If little is known about a species’ sensitivity to the herbicides used or you cannot find information on a particular cover crop species, looking at information on a close relative can give you a “guesstimate” of sensitivity. Planting a mixture of grass and broadleaf cover crops may also help increase the odds of successful establishment of at least one species in the mix. 

2. How long can I expect the herbicide remain active in the soil?

Herbicides can vary greatly in their persistence (length of time they remain active in the soil). If a product has soil activity, consider the half-life (the time it takes for 50% of the active ingredient to dissipate) of all active ingredients when evaluating risk to later-planted cover crops. Examples of herbicides with soil activity and a relatively long half-life include: Atrazine (60 days), Authority (32 to 302 days), Capreno (50 to 120 days), Classic (40 days), Corvus (50 to 120 days), Flexstar (100 days), Stinger (in Hornet and SureStart, 40 days), Pursuit (60-90 days), and Python (in Hornet and SureStart, 14 to 120 days). (Source: “Common corn and soybean herbicides, estimated half-lives, cash crop restrictions ant their potential to injure fall cover crops”, Penn State Extension, Curran and Lingenfelter, 2012. Available online.

Many factors, however, influence herbicide persistence. Soil pH, organic matter, cation exchange capacity, and clay content can increase herbicide persistence. Microbial activity also has a significant impact on herbicide persistence, and is the dominant mechanism of herbicide breakdown or degradation in the soil. Conditions favorable for microbial activity such as warm temperatures, adequate soil moisture, aerobic conditions, good fertility, and medium pH will favor herbicide breakdown. Herbicide degradation rates will generally increase with increases in temperature and moisture, while cool, dry conditions tend to slow degradation. As a result, dry and/or cool conditions the summer after herbicide application can result in increased risk of injury to a fall-seeded cover crop. 

3. When was the herbicide applied and when do I plan to seed the cover crop?

Much of the University research conducted to date looking at the sensitivity of cover crops to residual herbicides has been done with fall-seeded cover crops. One can expect that the longer the time period between herbicide application and cover crop seeding, the lower the risk of injury to the cover crop. As more farmers look at interseeding cover crops into standing corn and soybean, even more attention should be paid to persistence of the herbicide and cover crop sensitivity to the herbicides applied. Early interseeding of cover crops shortens the time window between herbicide application and cover crop seeding which may significantly limit herbicide and cover crop choices. Non-residual herbicides may result in the best chance for successful establishment when interseeding a cover crop, but the potential short and long-term risks of reduced weed control should be considered. 

4. Should I use a reduced rate of herbicide?

Reducing herbicide application rates to help reduce the risk of injuring a cover crop is a potential option, but this is not a recommended practice. Sub-lethal doses select for tougher-to-control weeds and can result in poor weed control that can impact cash crop yields and future weed control if weed escapes go to seed, replenishing the weed seedbank. Using the full-labeled rate of an herbicide is also a key tactic in the prevention and remediation of herbicide-resistant weeds. As previously discussed, many factors impact herbicide longevity in the soil, so using a reduced rate of herbicide could result in poor weed control but enough residual activity to hinder establishment and growth of a sensitive cover crop anyway. Considering the extent of herbicide-resistant weed populations in many fields across the state, it can be a risky proposition to potentially sacrifice long-term weed control by reducing herbicide application rates of residual herbicides. 

5. Should I increase my cover crop seeding rate? 

The question often arises regarding the possibility of increasing cover crop seeding rates if herbicide carryover is a concern. Increasing the seeding rate of the cover crop is a potential option to consider if the cover crop is marginally sensitive to the herbicide used. There are no guarantees, however, that a higher seeding rate would result in a higher stand of cover crop if the cover crop is sensitive to the herbicide used. Higher seeding rates will also result in higher cover crop seeding costs. Factors that influence the longevity and activity of the herbicide in the soil (as described previously) will influence how successful this tactic might be. 

6. Can I use a postemergence herbicide after inter-seeding my cover crop into corn or soybean early in the season?

No one wants to spend the time and money to interseed a cover crop early in the season to then end up killing it unintentionally with an herbicide used for weed control in corn or soybean. To best manage risk if you wish to apply an herbicide after interseeding a cover crop early in the season, only select an herbicide and cover crop combination that is allowed on the herbicide label, and follow application restrictions as listed on the label. 

Originally posted by University of Minnesota Extension

TAGS: Conservation
Hide comments

Comments

  • Allowed HTML tags: <em> <strong> <blockquote> <br> <p>

Plain text

  • No HTML tags allowed.
  • Web page addresses and e-mail addresses turn into links automatically.
  • Lines and paragraphs break automatically.
Publish